Honda CBR250R Forum : Honda CBR 250 Forums - Search Results
Advanced Search
Showing results 1 to 25 of 70
Search took 0.05 seconds.
Search: Posts Made By: gromit
Forum: CBR250 Service and Maintenance   06-20-2015, 08:19 PM
Replies: 1
Views: 354
Posted By gromit
front drive sprocket bolts (2) ----- 7 lbf-ft ...

front drive sprocket bolts (2) ----- 7 lbf-ft (ft/lbs)

rear sprocket nuts (6) ----- 55 lbf-ft (ft/lbs)
Forum: CBR250 New Member Introductions   04-15-2015, 09:26 AM
Replies: 92
Views: 4,193
Posted By gromit
What is going on here? New member First...

What is going on here?

New member
First post
72 replies
1,887 views
Still arguing the original point.

This is like a passive aggressive 'troll' at work.
Forum: CBR250 Problems and Issues   04-10-2015, 12:01 AM
Replies: 4
Views: 360
Posted By gromit
Take a look at the pic that shows the disassembly...

Take a look at the pic that shows the disassembly procedure.
Assembly is in the reverse order and it looks like no.3 the snap
clip might not be seated into the slot properly. That should have
been...
Forum: CBR250 Problems and Issues   03-27-2015, 11:37 AM
Replies: 10
Views: 679
Posted By gromit
When you shift you are ratcheting a star shaped...

When you shift you are ratcheting a star shaped plate that has a range of one
full shift up or one full shift down. Neutral is actually a 1/2 shift, the rider has
to become used to finding the...
Forum: CBR250 Problems and Issues   12-27-2014, 01:27 PM
Replies: 6
Views: 1,153
Posted By gromit
That is a jumper tool that is used on a number of...

That is a jumper tool that is used on a number of different Honda engines
for doing an ECU/ECM reset. During the reset procedure two of the connectors
have to be jumped and that connector...
Forum: CBR250 Service and Maintenance   11-04-2014, 11:36 AM
Replies: 357
  Sticky: DIY Oil Change
Views: 119,204
Posted By gromit
Sorry about that. Crush washers are usually...

Sorry about that.

Crush washers are usually flat washers made
from soft metal (aluminum or copper) so when
the drain plug is tightened the pressure will
deform the washer and form a seal,...
Forum: CBR250 Problems and Issues   09-18-2014, 01:14 PM
Replies: 46
Views: 5,177
Posted By gromit
Hey Clarko21 I'm back again. Lets go thru all...

Hey Clarko21 I'm back again.
Lets go thru all the bar weight parts, where they are
and what they do. There are only 6 parts plus the
handle bar grip itself. I don't want to bore you but lets
get...
Forum: CBR250 Problems and Issues   09-02-2014, 06:32 PM
Replies: 11
Views: 693
Posted By gromit
On the road I would plug just to not be stranded....

On the road I would plug just to not be stranded.
I would not run a front tire that was plugged but
I would run a plugged rear tire unless it was like
your puncture. It's right in the tread groove...
Forum: CBR250 Service and Maintenance   08-29-2014, 03:48 AM
Replies: 23
Views: 1,967
Posted By gromit
Everybody that has the opinion that it is not...

Everybody that has the opinion that it is not necessary
to clean and lube cables (especially the clutch cable),
change their minds when the clutch cable snaps when
you are riding. You can still...
Forum: CBR250 Appearance and Modifications   08-09-2014, 04:05 PM
Replies: 8
Views: 414
Posted By gromit
For the seat I use Meguiar's Motorcycle Vinyl and...

For the seat I use Meguiar's Motorcycle Vinyl and Leather Cleaner/Conditioner.
One of the nice features of it is that it does not leave a slippery finish on the
seat.
Forum: CBR250 Service and Maintenance   07-27-2014, 05:08 PM
Replies: 8
Views: 715
Posted By gromit
8mm allen

8mm allen
Forum: CBR250 Service and Maintenance   07-22-2014, 01:32 PM
Replies: 9
Views: 722
Posted By gromit
Thats exactly how it should look. That last...

Thats exactly how it should look.

That last post reminds me that you
can not believe everything you read
in the owners manual.

When doing an oil change the 'owners
manual' states a torque...
Forum: CBR250 Service and Maintenance   07-22-2014, 11:47 AM
Replies: 9
Views: 722
Posted By gromit
It's the air cleaner housing (air box) drain...

It's the air cleaner housing (air box) drain hose.
It collects anything that might accumulate in the
air box. If you see any liquid in the hose, pull the
the plug and drain it.

Not a big deal...
Forum: CBR250 Problems and Issues   07-14-2014, 01:11 PM
Replies: 9
Views: 676
Posted By gromit
If the above suggestions don't work, it could be...

If the above suggestions don't work, it could be that your
power band is not at factory specs and needs to be fixed.

See the attached pic for a replacement.

Good luck and let us know if it...
Forum: CBR250 Problems and Issues   05-26-2014, 05:05 PM
Replies: 6
Views: 354
Posted By gromit
This is the absolute last pic. I just took this...

This is the absolute last pic.
I just took this photo of my seat lock.
Forum: CBR250 Problems and Issues   05-26-2014, 04:15 PM
Replies: 6
Views: 354
Posted By gromit
This is my last try and the only other pic I...

This is my last try and the only other pic I could find.
Good Luck (you will figure it out sooner or later).
Forum: CBR250 Problems and Issues   05-24-2014, 02:49 PM
Replies: 2
Views: 299
Posted By gromit
see if this will help you

see if this will help you
Forum: Proficient Motorcycling: Riding Tips & Techniques   05-20-2014, 10:22 PM
Replies: 10
Views: 680
Posted By gromit
Near the beginning of the article is a drop box...

Near the beginning of the article is a drop box link that takes you to the full article
that is an 11 page pdf file that can be saved. It is much more extensive with pictures and examples.
Forum: Proficient Motorcycling: Riding Tips & Techniques   05-20-2014, 09:34 PM
Replies: 10
Views: 680
Posted By gromit
Very good post with valid points. I am putting in...

Very good post with valid points. I am putting in a link to an article written by
an RAF fighter pilot who has made a direct comparison from combat flying to
riding motorcycles. Among other things...
Forum: CBR250 Performance   05-02-2014, 10:51 AM
Replies: 13
Views: 1,189
Posted By gromit
Either google o2 sensor plug or go to most any...

Either google o2 sensor plug or go to most any motorcycle accessory site.
There are a number of sweet looking sensor plugs available at good prices.
Forum: CBR250 Service and Maintenance   04-05-2014, 03:35 PM
Replies: 30
Views: 2,152
Posted By gromit
A word or two of caution !!! The little...

A word or two of caution !!!

The little owners manual that comes with the bike states a torque value for the oil cover bolts that is too high and a significant number of people have snapped the...
Forum: CBR250 Appearance and Modifications   03-23-2014, 09:15 PM
Replies: 7
Views: 837
Posted By gromit
It's easy to remove (one mounting screw and it...

It's easy to remove (one mounting screw and it wiggles off a couple short slide hooks toward the back). You don't want to get any overspray on the bike and a light sanding gives the new paint a good...
Forum: CBR250 Problems and Issues   03-12-2014, 07:05 PM
Replies: 14
Views: 1,636
Posted By gromit
Use the search feature in the upper menu bar...

Use the search feature in the upper menu bar (enter rear lockable seat stuck - select show threads - click go). There is a really good mini tutorial with pics showing how to make a tool from a wire...
Forum: CBR250 Appearance and Modifications   02-26-2014, 10:14 AM
Replies: 7
Views: 837
Posted By gromit
My answer is ( yes - no - maybe - probably not )....

My answer is ( yes - no - maybe - probably not ). The silver heat shield has a satin rather than a high gloss finish. If the scratch can be felt with your finger nail it won't work. The satin finish...
Forum: Off Topic Discussion   02-18-2014, 08:46 AM
Replies: 169
Views: 6,370
Posted By gromit
stirrups

You all are going to be soooo jealous when I get the final mounting position sorted out.
Showing results 1 to 25 of 70

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome